Zebra XiIIIPlus User Manual download pdf (Page 121)

Routine Maintenance

Replace Fuse

23063L-001 Rev. 2 6/21/2004 RXiIIIPlus User Guide 97

Figure 46 • Fuse Locations

3. Snap the fuse holder back into the AC power entry module.

4. Reconnect the power cord, and turn the printer On (I).

In-circuit fuse

Fuse holder

Spare fuse

Note • If the printer does not power on, an internal component failure may have occurred,

and the printer requires servicing by an authorized service technician.

1 2 ... 116 117 118 119 120 121 122 123 124 125 126 ... 151 152

User Guide 1
Contents 5
Proprietary Statement 9
Liability Disclaimer 10
Limitation of Liability 10
Warranty Information 11
Related Hardware Items 12
Repair Services 13
Printer Software 15
License Agreement 15
3. RESTRICTIONS 16
Contacts 22
Document Conventions 23
Related Documents 24
Introduction 25
Exterior View 26
Front Panel 27
Front Panel Buttons 28
Front Panel Lights 29
Printer Components 30
Printer Setup 31
Before You Begin 32
Report Shipping Damage 33
Store or Reship the Printer 33
Select a Site for the Printer 34
Power Cord Specifications 35
Data Cable Requirements 37
Types of Media 38
Non-Continuous Media 39
Continuous Media 39
(label profile) 40
When to Use Ribbon 41
Ribbon Width 41
Coated Side of Ribbon 41
Adhesive Test 42
Ribbon Scratch Test 42
If the ribbon... Then 43
Printer Operation 45
Load the Printer 46
Load Fanfold Media 48
Load Ribbon 50
8. Close the printhead 53
Remove Used Ribbon 54
PRINTER 55
PRINTER READY 55
Calibrate the Printer 57
Adjust and Calibrate Sensors 58
11. Close the printhead 59
Transmissive (Media) Sensors 60
Toggle Position Adjustment 62
Printhead Pressure Adjustment 62
6. Tighten the locking nuts 63
Front Panel Controls 65
Overview 66
Password-Protected Parameters 67
Front Panel LCD 68
PRINT MODE 69
MEDIA TYPE 69
SENSOR TYPE 69
PRINT METHOD 69
PRINT WIDTH 70
MAXIMUM 70
Parameter Action/Explanation 71
1. When the LCD displays 72
2. Do you wish to continue? 72
DELIMITER 77
ZPL MODE 77
LABEL TOP 79
POSITION 79
VERIFIER 79
ZebraNet 83
RFID Guidelines 85
Transponder Placement 86
ZPL II Commands for RFID 87
Host Verification 88
RFID Setup 89
^RS,800,,2,P^FS 90
^RS,800,500,2,P^FS 91
Read Tag 92
Write Tag 93
Sample of RFID Programming 94
Parallel Port 98
36-Pin Connectors Description 99
Serial Port 100
Serial Pin Configuration 101
RS-232 Interface Connections 102
DB-9 to DB-25 Connections 103
Modem Connection 103
Data Ports 104
USB 2.0 Port 105
Memory Cards 107
PCMCIA Memory Card 108
CompactFlash Card 110
1. Turn the AC power Off (O) 110
Routine Maintenance 113
Cleaning Schedule 114
Clean Exterior 114
CLEAN HEAD NOW 114
Clean Interior 115
1. Open the printhead 115
7. Close the printhead 116
Snap Plate 119
Replace Fuse 120
Troubleshooting 123
LCD Error Messages 125
RIBBON IN 126
HEAD TOO HOT 126
HEAD COLD 127
OUT OF MEMORY 127
Print Quality Problems 128
Communications Problems 130
Printer Diagnostics 132
1. Turn Off (O) the printer 133
Specifications 137
Features 138
Bar Codes 139
Compliance for All Printers 139
General Specifications 140
Print Specifications by Model 141
Ribbon Specifications 142
Label Specifications 143
CHECK RIBBON 145
HEAD ELEMENT BAD 146
HEAD OPEN 146
PAPER OUT 148
Ribbon Out 149
Customer Order # 23063L-001 152

Comments to this Manuals

No comments

Zebra XiIIIPlus User Manual Page 121

Comments to this Manuals

Related products and manuals for Label printers Zebra XiIIIPlus