Zebra XiIIIPlus User Manual Page 119
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Routine Maintenance
Clean Interior
23063L-001 Rev. 2 6/21/2004 RXiIIIPlus User Guide 95
Snap Plate
Clean the snap plate when label adhesive or a label is stuck to the underside. Figure 44 shows
the location of the snap plate.
Figure 44 • Snap Plate
To clean the snap plate, complete these steps:
1. Remove the two screws that secure the snap plate to the antenna support frame.
2. Remove the snap plate from the printer.
3. Clean the snap plate with cleaning solvent and a soft cloth.
4. To reinstall the snap plate, slide it back into place until the screw holes on the snap plate
line up with the screw holes in the antenna support frame.
5. Reinstall the two snap plate screws to secure the snap plate to the antenna support frame.
1
Antenna support screws
2
Location of right-side snap plate screw
(screw not shown)
3
Snap plate
4
Antenna support
5
Antenna support frame
6
Left-side snap plate screw
1
6
5
2
4
3
Important • Do not remove the antenna support screws.
- User Guide 1
- Contents 5
- Proprietary Statement 9
- Liability Disclaimer 10
- Limitation of Liability 10
- Warranty Information 11
- Related Hardware Items 12
- Repair Services 13
- Printer Software 15
- License Agreement 15
- 3. RESTRICTIONS 16
- Contacts 22
- Document Conventions 23
- Related Documents 24
- Introduction 25
- Exterior View 26
- Front Panel 27
- Front Panel Buttons 28
- Front Panel Lights 29
- Printer Components 30
- Printer Setup 31
- Before You Begin 32
- Report Shipping Damage 33
- Store or Reship the Printer 33
- Select a Site for the Printer 34
- Power Cord Specifications 35
- Data Cable Requirements 37
- Types of Media 38
- Non-Continuous Media 39
- Continuous Media 39
- (label profile) 40
- When to Use Ribbon 41
- Ribbon Width 41
- Coated Side of Ribbon 41
- Adhesive Test 42
- Ribbon Scratch Test 42
- If the ribbon... Then 43
- Printer Operation 45
- Load the Printer 46
- Load Fanfold Media 48
- Load Ribbon 50
- 8. Close the printhead 53
- Remove Used Ribbon 54
- PRINTER 55
- PRINTER READY 55
- Calibrate the Printer 57
- Adjust and Calibrate Sensors 58
- 11. Close the printhead 59
- Transmissive (Media) Sensors 60
- Toggle Position Adjustment 62
- Printhead Pressure Adjustment 62
- 6. Tighten the locking nuts 63
- Front Panel Controls 65
- Overview 66
- Password-Protected Parameters 67
- Front Panel LCD 68
- PRINT MODE 69
- MEDIA TYPE 69
- SENSOR TYPE 69
- PRINT METHOD 69
- PRINT WIDTH 70
- MAXIMUM 70
- Parameter Action/Explanation 71
- 1. When the LCD displays 72
- 2. Do you wish to continue? 72
- DELIMITER 77
- ZPL MODE 77
- LABEL TOP 79
- POSITION 79
- VERIFIER 79
- ZebraNet 83
- RFID Guidelines 85
- Transponder Placement 86
- ZPL II Commands for RFID 87
- Host Verification 88
- RFID Setup 89
- ^RS,800,,2,P^FS 90
- ^RS,800,500,2,P^FS 91
- Read Tag 92
- Write Tag 93
- Sample of RFID Programming 94
- Parallel Port 98
- 36-Pin Connectors Description 99
- Serial Port 100
- Serial Pin Configuration 101
- RS-232 Interface Connections 102
- DB-9 to DB-25 Connections 103
- Modem Connection 103
- Data Ports 104
- USB 2.0 Port 105
- Memory Cards 107
- PCMCIA Memory Card 108
- CompactFlash Card 110
- 1. Turn the AC power Off (O) 110
- Routine Maintenance 113
- Cleaning Schedule 114
- Clean Exterior 114
- CLEAN HEAD NOW 114
- Clean Interior 115
- 1. Open the printhead 115
- 7. Close the printhead 116
- Snap Plate 119
- Replace Fuse 120
- Troubleshooting 123
- LCD Error Messages 125
- RIBBON IN 126
- HEAD TOO HOT 126
- HEAD COLD 127
- OUT OF MEMORY 127
- Print Quality Problems 128
- Communications Problems 130
- Printer Diagnostics 132
- 1. Turn Off (O) the printer 133
- Specifications 137
- Features 138
- Bar Codes 139
- Compliance for All Printers 139
- General Specifications 140
- Print Specifications by Model 141
- Ribbon Specifications 142
- Label Specifications 143
- CHECK RIBBON 145
- HEAD ELEMENT BAD 146
- HEAD OPEN 146
- PAPER OUT 148
- Ribbon Out 149
- Customer Order # 23063L-001 152
- © 2004 ZIH Corp 152
Related products and manuals for Label printers Zebra XiIIIPlus
Label printers Zebra SAP R/3 User Manual
(8 pages)
(8 pages)
Label printers Zebra P320 User Manual
(2 pages)
(2 pages)
Label printers Zebra ZT210 User Manual
(168 pages)
(168 pages)
Label printers Zebra Z4Mplus User Manual
(178 pages)
(178 pages)
Label printers Zebra QL+ User Manual
(86 pages)
(86 pages)
Label printers Zebra PA/PT 400 User Manual
(44 pages)
(44 pages)
Label printers Zebra GX420 User Manual
(4 pages)
(4 pages)
Label printers Zebra PA400 User Manual
(58 pages)
(58 pages)
Label printers Zebra Cameo User Manual
(22 pages)
(22 pages)
Label printers Zebra 79695L-002 User Manual
(156 pages)
(156 pages)
Label printers Zebra ZM400 User Manual
(33 pages)
(33 pages)
Label printers Zebra Z4M User Manual
(102 pages)
(102 pages)
Label printers Zebra AM16629-1 User Manual
(12 pages)
(12 pages)
Label printers Zebra A100 User Manual
(28 pages)
(28 pages)
Label printers Zebra ZP 450 User Manual
(82 pages)
(82 pages)
Label printers Zebra XiII-Series User Manual
(118 pages)
(118 pages)
Label printers Zebra XiIII Series User Manual
(116 pages)
(116 pages)
Label printers Zebra Z4M User Manual
(57 pages)
(57 pages)
Label printers Zebra 105SL User Manual
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 1.605 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals