Zebra S400 User's Guide Page 108
- Page / 146
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
Troubleshooting Checklists
100
79695L-001 Rev. A ZM400/ZM600 User Guide 3/27/07
Troubleshooting Checklists
If an error condition exists with the printer, review this checklist:
Is there an error message on the LCD? If yes, see LCD Error Messages on page 101.
Are noncontinuous labels being treated as continuous labels? If yes, see Calibrate Media
and Ribbon Sensor Sensitivity on page 74.
Is the printer reporting a ribbon error when ribbon is loaded properly? If yes, see Calibrate
Media and Ribbon Sensor Sensitivity on page 74.
Are you experiencing problems with print quality? If yes, see Print Quality Problems
on page 105.
Are you experiencing communications problems? If yes, see Communications Problems
on page 109.
If the labels are not printing or advancing correctly, review this checklist:
Are you using the correct type of labels? Review the types of label in Types of Media
on page 25.
Are you using a label that is narrower than the maximum print width? See Set Print Width
on page 66.
Review the label- and ribbon-loading illustrations in Load Media on page 33 and Load
Ribbon on page 47.
Does the printhead need to be adjusted? See Adjust Printhead Pressure on page 53for
more information.
Do the sensors need to be calibrated? See Calibrate Media and Ribbon Sensor Sensitivity
on page 74 for more information.
If none of the above suggestions correct the problem, review this checklist:
Perform one or more of the self-tests given in Printer Diagnostics on page 113. Use the
results to help identify the problem.
If you are still having problems, see Contacts on page 3 for customer support information.
- ZM400/ZM600 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 17
- Control Panel 18
- Control Panel Buttons 19
- Control Panel Lights 20
- Printer Language Modes 21
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- I) may damage the 28
- O) position 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- Ribbon Scratch Test 36
- Operations 37
- Media Paths 39
- Media Path 40
- Load Media 41
- Rear Feed 42
- Bottom Feed 42
- Roll Media (Continued) 43
- Fanfold Media (Continued) 43
- PAUSE to enable printing 44
- Close the printhead assembly 54
- Load Ribbon 55
- Ribbon Coated Outside 57
- (black ribbon spindle) 57
- Ribbon Coated Inside 57
- (gray ribbon spindle) 57
- Remove Used Ribbon 59
- Calibrate the Printer 60
- Adjust Printhead Pressure 61
- Inside Dial Outside Dial 62
- Configuration 63
- Setup Mode 64
- Exit Setup Mode 65
- Default Password Value 66
- Print a Configuration Label 67
- LIST NETWORK 68
- Control Panel Parameters 69
- Standard Printer Parameters 70
- To change the value shown: 71
- Parameter 71
- ZM400 ZM600 74
- Action/Explanation 75
- WARNING REPLACE 77
- To format a memory card: 80
- To initialize Flash memory: 81
- To print a sensor profile: 81
- LOAD BACKING prompt displays 82
- RELOAD ALL displays 82
- To skip these parameters: 90
- IDLE DISPLAY 92
- Replacing Printer Components 96
- Lubrication 96
- Clean the Exterior 97
- Routine Maintenance 100
- Cleaning Procedures 100
- Clean the Cutter Module 102
- I) the printer 103
- Troubleshooting 107
- Troubleshooting Checklists 108
- LCD Error Messages 109
- O) the printer 110
- HEAD COLD 111
- HEAD TOO HOT 111
- DEFRAGMENTING 112
- ERROR CONDITION 112
- CUTTER JAM 112
- OUT OF MEMORY 112
- (function) 112
- Print Quality Problems 113
- Note • A vertical drift of 115
- Calibration Problems 116
- Communications Problems 117
- Ribbon Problems 118
- LANGUAGE 119
- SAVE CHANGES in the 119
- Printer Diagnostics 121
- CANCEL Self Test 122
- PAUSE Self Test 123
- FEED Self Test 124
- Print Quality Description 126
- FEED and PAUSE Self Test 127
- Sensor Profile 129
- Specifications 131
- General Specifications 132
- Agency Approvals 133
- Printing Specifications 134
- Media Specifications 136
- Ribbon Specifications 137
- Printer Options 138
- Cutter Jam message, 104 140
- HEAD COLD message 140
- HEAD ELEMENT BAD message, 102 140
- HEAD TOO HOT message, 103 140
- INVALID HEAD message, 101 141
- OUT OF MEMORY message, 104 141
- PAPER OUT message, 102 142
- RIBBON IN message, 102 143
- RIBBON OUT message, 101 143
- THERMISTOR FAULT message 144
- © 2007 ZIH Corp 146
Related products and manuals for Label printers Zebra S400
Label printers Zebra TTPM2 Specifications
(102 pages)
(102 pages)
Label printers Zebra TLP 3842 User Manual
(40 pages)
(40 pages)
Label printers Zebra 140XiIII Plus User's Guide
(166 pages)
(166 pages)
Label printers Zebra A300 User's Guide
(38 pages)
(38 pages)
Label printers Zebra 105SL Specifications
(246 pages)
(246 pages)
Label printers Zebra A300 User's Guide
(36 pages)
(36 pages)
Label printers Zebra S400 User Manual
(46 pages)
(46 pages)
Label printers Zebra S4M Specifications
(404 pages)
(404 pages)
Label printers Zebra LP 2824-Z User Manual
(28 pages)
(28 pages)
Label printers Zebra Z6M User Manual
(112 pages)
(112 pages)
Label printers Zebra XiIIIPlus User Manual
(152 pages)
(152 pages)
Label printers Zebra SAP R/3 User Manual
(8 pages)
(8 pages)
Label printers Zebra P320 User Manual
(2 pages)
(2 pages)
Label printers Zebra ZT210 User Manual
(168 pages)
(168 pages)
Label printers Zebra Z4Mplus User Manual
(178 pages)
(178 pages)
Label printers Zebra QL+ User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 0.864 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals