Zebra A300 User's Guide

User's GuideT300ZebraCustomer order #547000LManufacturer part #547000LB© Zebra Technologies CorporationZEBRA PERSONAL PRINTER LINE™THERMAL TRANSF

78547000r1 Page 5 Tuesday, March 25, 1997 11:38 AM

9547000r1 Page 6 Tuesday, March 25, 1997 11:38 AM

1011547000r1 Page 7 Tuesday, March 25, 1997 11:38 AM

12547000r1 Page 8 Tuesday, March 25, 1997 11:38 AM

12 547000r1 Page 9 Tuesday, March 25, 1997 11:38 AM

12547000r1 Page 10 Tuesday, March 25, 1997 11:38 AM

Figure 2. Parallel Connection547000r1 Page 11 Tuesday, March 25, 1997 11:38 AM

Figure 3. Serial Connection547000r1 Page 12 Tuesday, March 25, 1997 11:38 AM

Note: If you plan to use BAR-ONE™ software to create your labels, you will need to install the software on your computer before you can operate your p

The Zebra T300 printer uses the Windows™-based BAR-ONE software or ZPL II Programming Language commands. To install BAR-ONE software:1. Start Windows.

Zebra T300 PrinterUser’s GuideCustomer order # 547000LManufacturer part # 547000LB Rev. 1547000r1 Page -3 Tuesday, March 25, 1997 11:38 AM

Located on the rear of the printer. The power switch should be turned off before connecting or disconnecting any cables.In normal use, pressing the Fe

Turn the printer on by pressing the Power Switch on the rear of the printer. The Power light will turn on. The printer performs a set of internal diag

A set screw is located on top of the Printhead Carrier Assembly that can be adjusted to control print quality. This adjustment is set at the factory a

Zebra A300 & T300User's GuideAddendum1C:\A_Series\A_T_Adden.vpWed Aug 12 10:52:06 1998Color profile: DisabledComposite Default screen

ScopeThisaddendumcontainsinformationaboutthenewCalibrationfeaturesaddedtotheZebraA300andZebraT300printerswhenupgradedwiththe25.8.1and23.8.1and later v

Manual CalibrationManual calibration should be performed whenever you are using pre-printed labels or preprinted label backing, or if the printer will

© Zebra Technologies Corporation Part # 55560L Rev. 1Figure 2. T300 Sample Media Sensor ProfileFigure 1. A300 Sample Media Sensor Profile4C:\A_Series\

This calibration procedure should be performed the first time you use the printer and any time you change the type of media in the printer.1. Turn the

9600 baud, 8 bit word length, no parity, and 1 stop bit. Then, set the communications parameters on your computer to match this.• If you need to use d

CAUTION: Use only the cleaning agents indicated in Table 4. Zebra Tech-nologies Corporation will not be responsible for damage caused by any other flu

This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating

Table 5. TroubleshootingPower light does not turn on when Power switch is turned on.Printer is not receiving power.Make sure that the power supply is

To print out a listing of the printer’s current configuration (configuration label), refer to Table 2, “Feed Key Troubleshooting Modes,” on page 15.If

Figure 8: Communications Diagnostics Printout (Sample)547000r1 Page 23 Tuesday, March 25, 1997 11:38 AM

Print density 203 dots/inch 8 dots/mmPrint width 1 to 4.125 25.4 mm to 105.0 mmPrint speed 2 /sec, 1.5 /sec 51 mm/sec, 38 mm/secLabel width (includin

Ribbon requirements Zebra recommends use of Zebra-brand ribbon which is inked on the inside surface. (Use tape to see which side is inked.)Fonts avail

Figure 9. 230 VAC Power Line CordFigure 10. Examples of International Safety OrganizationsTable 6. Parallel Pinouts1 Strobe2-9 Data Bits 0-710 Acknowl

The enclosed software and documentation are protected by the United States copyright law and international treaty, and there-fore you must treat them

1. Printer WarrantyZEBRA printers, excluding thermal printheads which are warranted separately below, are warranted against defects in material or wor

User's GuideT300ZebraCustomer order #547000LManufacturer part #547000LB© Zebra Technologies CorporationZEBRA PERSONAL PRINTER LINE™THERMAL TRANSF

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Unpacking and Inspection. . . . . . .

Figure 1. Printer Overview Cover latches Media cover Media spindle guide Printhead release lever Media guide Peel-off release lever Peel

This manual provides all of the information you will need to operate your printer. To print labels, tags, or tickets with the Zebra T300 printer, refe

12547000r1 Page 2 Tuesday, March 25, 1997 11:38 AM

3 Ensure switch is set to Thermal Transfer Mode.4547000r1 Page 3 Tuesday, March 25, 1997 11:38 AM

56547000r1 Page 4 Tuesday, March 25, 1997 11:38 AM