Zebra 105SL User Manual Page 82
- Page / 130
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
58 105SL User Guide 6/4/2004 11342L Rev. 8
Configuration
Configuration and Calibration LCD Displays
ESSID
2
ESSID
This parameter cannot be changed through the front panel.
AUTH. TYPE
2
Authentication Type
Default: OPEN
Selections: OPEN, SHARED
LEAP MODE
3
An encryptio n method that is ava ilable with some wireless cards. Set th e LEAP user
name and password through the printer web pages.
Accepted Values: ON , OFF
Default Value: OFF
ENCRYPTION
MODE
2
Encryption Mode
Default: OFF
Selections: OFF, 40-BIT, 128-BIT
ENCRYPTION
INDEX
2
Encryption Index
Default: 1
Selections: 1, 2, 3, 4
RESET NETWORK
1
Reset Network
This option resets t he wireless card and t he print server when the wireless opti on is
running. Selecting thi s op tion has no effect when the wireless option is not running,
when there is no card inserted, or when the wireless password is anything other than
the default (zero).
1. Press the (+) key to select
YES
.
The LCD prompts
ARE YOU SURE?
.
• Press the (–) key to select
NO
to cancel the request.
• Press the (+) key to select
YES
and reset the network.
Table 7 • Print Server LCD Displays (Continued)
LCD Explanation
1 These parameters appear after the system recognizes the existence of a ZebraNet print server (wired or wireless). After the
print server is recognized, all zeroes (000.000.000.000) will display until the printer obtains an IP address or defaults to
address 192.168.254.254.
2 Appears only when t he ZebraNet Wireless Print Server is inst alled.
3 This parameter appears 1) when no wireless card is inserted or 2) when the wireless card is associated to the WLAN and the
card supports LEAP.
- User Guide 1
- Proprietary Statement 9
- Liability Disclaimer 10
- Limitation of Liability 10
- Warranty Information 11
- Related Hardware Items 12
- Repair Services 13
- Printer Software 15
- License Agreement 15
- 3. RESTRICTI ONS 16
- Contents 21
- Contacts 22
- Document Conventions 23
- Related Documents 24
- Introduction 25
- Exterior View 26
- Operator Controls 27
- Front Panel Keys 28
- Front Panel Lights 29
- Printer Interior 30
- Printer Setup 31
- Before You Begin 32
- Report Damage 33
- Select a Site for the Printer 34
- Power Cord Specifications 35
- Cable Requirements 39
- Types of Media 40
- Non-Continuous Media 41
- Continuous Media 41
- When to Use Ribbon 42
- Ribbon Width 42
- Coated Side of Ribbon 42
- Adhesive Test 43
- Ribbon Scratch Test 43
- If the ribbon... Then 44
- Printer Operation 45
- Roll Media Loading 46
- Peel-Off Mode 47
- Rewind Mode 48
- Cutter Mode 50
- Peel-Only Mode 51
- Removing the Label Liner 52
- Fanfold Media Loading 53
- Ribbon Loading 54
- Ribbon Removal 56
- Print a Configuration Label 57
- LIST NETWORK 58
- Calibrate the Printer 59
- Adjust and Calibrate Sensors 60
- Adjust and Calibrate Sens ors 61
- Black Mark Sensor 63
- Configuration 65
- Overview 66
- Exit Setup Mode 67
- Password-Protected Parameters 68
- Basic Printer Configuration 69
- Parameter Action/Explanation 70
- MEDIA TYPE 71
- SENSOR TYPE 71
- PRINT METHOD 71
- PRINT WIDTH 71
- MAXIMUM LENGTH 71
- PROTOCOL 76
- NETWORK ID 76
- COMMUNICATIONS 76
- CONTROL PREFIX 77
- FORMAT PREFIX 77
- DELIMITER CHAR 77
- ZPL MODE 77
- MEDIA POWER UP 77
- HEAD CLOSE 78
- BACKFEED 78
- LABEL TOP 78
- LEFT POSITION 78
- LCD ADJUST 80
- LANGUAGE 80
- ZebraNet 81
- LCD Explanation 82
- Data Ports 83
- Serial Data Port 84
- RS-232 Interface Connections 85
- Parallel Data Port 88
- Memory Cards 89
- PCMCIA Memory Card 90
- PCMCIA Memo ry Card 91
- CompactFlash Card 92
- Cleaning Schedule 96
- Cleaning the Interior 97
- Snap Plate 98
- Cutter Module 99
- Lubrication 100
- Fuse Replacement 100
- Adjustments 101
- Routine Maintenance 102
- Troubleshooting 103
- LED Error Messages 104
- Print Quality Problems 106
- Communications 108
- Printer Diagnostics 109
- CANCEL Self Test 110
- PAUSE Self Test 111
- FEED Self Test 112
- FEED and PAUSE Self Test 113
- Specifications 115
- Bar Codes 117
- General Specifications 117
- Printing Specifications 118
- Ribbon Specifications 119
- Font Specifications 119
- 300 dpi (12 dots/mm) 120
- Media Specifications 121
- CHECK RIBBON 123
- Customer Order # 11342L 130
- © 2004 ZIH Corp 130
Related products and manuals for Label printers Zebra 105SL
Label printers Zebra Printers User Manual
(69 pages)
(69 pages)
Label printers Zebra LI 72 User Manual
(62 pages)
(62 pages)
© 2020, manymanuals.com. All rights reserved. | 0.199 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals