Zebra 105SL User Manual Page 71
- Page / 130
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration
Configuration and Calibration LCD Displays
11342L Re v. 8 6/4/2004 105SL User Guide 47
MEDIA TYPE
Setting Media Type: Press the (+) or (–) key to display other choices.
Default: Non-Contin uo us
Selections: Continuous, non-contin uo us
This parameter tell s the prin ter the ty pe of media yo u are using . Selecting continuous
media requires that you include a label length instruction in your label format
(^LLxxxx if you are using ZPL or ZPL II).
When non-con tin uo us media is selected, the printer feeds media to calculate label
length (the distance between two detections of the inter-label gap, webbing, or
alignment notch or hole).
SENSOR TYPE
Setting the Sensor Type: Press the (+) or (–) key to di spl ay other choices.
Default: We b
Selections: We b , m a r k
This parameter te lls the printer whether you are using media with a web (gap/space
between lab els, notch, or ho le ) to indicate the separations between labels or if you are
using media with a black mark printed on the back. If your media does not have black
marks on the back, leave your printer at the default (web).
PRINT METHOD
Selecting Print Method: Press the (+) key for the next value; press the (–) key for the
previous value.
Default: Thermal transfer
Selections: Thermal transfer, direct thermal
The print method parameter tells the printer the method of printing you wish to use:
direct thermal (no ribbon) or thermal transfer (using thermal transfer media and
ribbon).
Note • Selecting direct thermal wh en using ther mal transfer media and ribbon creates a
warning condition, but printing continues.
PRINT WIDTH
Setting Print Width: Press the (+ ) key to increase the v alue, press the (–) key to toggle
to a different digit. To change the unit of measurement, press t he (–) key until th e u nit
of measurement is active, then press the (+) key to toggle to a di f f erent unit of measure
(inches, mm, or dots).
Default; Range:The default and range of acceptable values vary depend in g on which
printer you have. Refer to Printing Specifications on page 94 for further information
about the ranges available for your model.
Print width determines the printable area across the width of the label.
MAXIMUM LENGTH
Setting Maximum Length: Press the (–) key to decrease the valu e, press the (+) key to
increase the value.
Default; Range:The default and range of acceptable values vary dependin g on your
printer ’s configuration. Values are adjustable in 1 in. (25.4 mm) increments.
Maximum length is used in conjunction w ith the calibration proced ure. The value of
this setting determines the maximum label length used during the media portion of the
calibration process. Only a few labels are needed to set media sensors. Always set the
value that is closest to, but not lower than, the length of the label you are using. For
example, if the length of the label is 14.5 in. (368 mm), set the parameter for 15.0 in.
(381 mm).
Table 6 • Printer Parameters (Sheet 2 of 11)
Parameter Action/Explanation
- User Guide 1
- Proprietary Statement 9
- Liability Disclaimer 10
- Limitation of Liability 10
- Warranty Information 11
- Related Hardware Items 12
- Repair Services 13
- Printer Software 15
- License Agreement 15
- 3. RESTRICTI ONS 16
- Contents 21
- Contacts 22
- Document Conventions 23
- Related Documents 24
- Introduction 25
- Exterior View 26
- Operator Controls 27
- Front Panel Keys 28
- Front Panel Lights 29
- Printer Interior 30
- Printer Setup 31
- Before You Begin 32
- Report Damage 33
- Select a Site for the Printer 34
- Power Cord Specifications 35
- Cable Requirements 39
- Types of Media 40
- Non-Continuous Media 41
- Continuous Media 41
- When to Use Ribbon 42
- Ribbon Width 42
- Coated Side of Ribbon 42
- Adhesive Test 43
- Ribbon Scratch Test 43
- If the ribbon... Then 44
- Printer Operation 45
- Roll Media Loading 46
- Peel-Off Mode 47
- Rewind Mode 48
- Cutter Mode 50
- Peel-Only Mode 51
- Removing the Label Liner 52
- Fanfold Media Loading 53
- Ribbon Loading 54
- Ribbon Removal 56
- Print a Configuration Label 57
- LIST NETWORK 58
- Calibrate the Printer 59
- Adjust and Calibrate Sensors 60
- Adjust and Calibrate Sens ors 61
- Black Mark Sensor 63
- Configuration 65
- Overview 66
- Exit Setup Mode 67
- Password-Protected Parameters 68
- Basic Printer Configuration 69
- Parameter Action/Explanation 70
- MEDIA TYPE 71
- SENSOR TYPE 71
- PRINT METHOD 71
- PRINT WIDTH 71
- MAXIMUM LENGTH 71
- PROTOCOL 76
- NETWORK ID 76
- COMMUNICATIONS 76
- CONTROL PREFIX 77
- FORMAT PREFIX 77
- DELIMITER CHAR 77
- ZPL MODE 77
- MEDIA POWER UP 77
- HEAD CLOSE 78
- BACKFEED 78
- LABEL TOP 78
- LEFT POSITION 78
- LCD ADJUST 80
- LANGUAGE 80
- ZebraNet 81
- LCD Explanation 82
- Data Ports 83
- Serial Data Port 84
- RS-232 Interface Connections 85
- Parallel Data Port 88
- Memory Cards 89
- PCMCIA Memory Card 90
- PCMCIA Memo ry Card 91
- CompactFlash Card 92
- Cleaning Schedule 96
- Cleaning the Interior 97
- Snap Plate 98
- Cutter Module 99
- Lubrication 100
- Fuse Replacement 100
- Adjustments 101
- Routine Maintenance 102
- Troubleshooting 103
- LED Error Messages 104
- Print Quality Problems 106
- Communications 108
- Printer Diagnostics 109
- CANCEL Self Test 110
- PAUSE Self Test 111
- FEED Self Test 112
- FEED and PAUSE Self Test 113
- Specifications 115
- Bar Codes 117
- General Specifications 117
- Printing Specifications 118
- Ribbon Specifications 119
- Font Specifications 119
- 300 dpi (12 dots/mm) 120
- Media Specifications 121
- CHECK RIBBON 123
- Customer Order # 11342L 130
- © 2004 ZIH Corp 130
Related products and manuals for Label printers Zebra 105SL
Label printers Zebra Printers User Manual
(69 pages)
(69 pages)
Label printers Zebra LI 72 User Manual
(62 pages)
(62 pages)
© 2020, manymanuals.com. All rights reserved. | 0.492 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals