Zebra TTP2130 Specifications Page 65
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
65
Programming
Software Command Syntax
09/28/2009 TTP 2100 Technical Manual P1003640-002
The printer stores its configuration settings in an EEPROM. When the printer is powered on,
the values are loaded from the EEPROM. Using this command, a parameter value can be
temporarily overridden. The value can later be made permanent with the ESC & 4 command.
Permanently stored values are loaded after a printer reset or at power on.
Set Several Parameters at Once
You can use this command to set multiple parameters at once. The format for this option is as
follows:
ESC & P 000 n2 n3 data
When operating in this mode, specify a value of 0 for n1, the first parameter you want to set for
n2, and the number of parameters to set for n3, followed immediately by the parameter data.
To set parameters that extend over a range in which the parameter number is not defined,
specify 0 for the parameters that do not exist. For example, to set n4 to n7, you must provide
all four parameters in data even though n6 does not exist.
per
Store parameters permanently by sending <ESC>&<4>.
This command is only valid for the following:
• TTP 2110, Serial No. higher than 2-0913-27444
• TTP 2130, Serial No. higher than 2-0913-27471
The TOF sensor has its own firmware that can be upgraded using this command.
ESC & P n1...n2
Set Parameter Value
1B 26 50 n1...n2 hex
27 38 80 n1...n2 decimal
n1 Parameter number, range 1 -255.
n2 Parameter value. Refer to Default Parameter Settings on page 81 for
information about the valid range for each parameter number.
Example • This example sets the first 5 tabs to 5, 10, 15, 20, and 25. (n2 = 5, n3 = 5)
<ESC>&P<000><015><005><005><010><015><020><025>
ESC & s n1
Load SPI Slave Firmware
1B 26 73 0A Hex
27 38 115 10 Decimal
n1 SPI Slave address, for the sensor board, the address is 10 dec.
<file> the bin file with the new firmware
- TTP 2100 1
- Technical Manual 1
- Contents 3
- Introduction 7
- Contacts 8
- Product Presentation 10
- Eject Mode 12
- Hold Mode 12
- Print and drop 12
- Print and take 12
- Controls 13
- Power Indicator 14
- Status Indicator 14
- Description 14
- Installation 15
- Paper Width Setting 16
- Value When Used 16
- 10. Select Upload One 17
- Top of Form (TOF) Sensor 18
- Calibrating the TOF Sensor 19
- Installation Considerations 20
- Orientation 21
- Push down 22
- Design Your Own Mounting 23
- Ambient Light 24
- Paper low 25
- Connector 25
- TTP 2110 26
- TTP 2130 27
- Housing: 29
- Tyco No. 350777-1 29
- Socket: 29
- Tyco No. 350689-1 29
- Making a Self-Test Printout 30
- Installing a Printer Driver 32
- Operation 33
- Temperature-sensitive 34
- SW96074C 34
- SW96075C 34
- Wrong! Wrong! Wrong! 35
- 1. Open the printer lid 36
- Programming 37
- Figure 24 • Printout Styles 38
- ESC ! n1 39
- Select font 39
- 1B 23 Hex 43
- 27 35 Decimal 43
- 1B 5A Hex 43
- 27 90 Decimal 43
- Text Commands 44
- 1B 21 n1 hex 45
- 27 33 n1 decimal 45
- 1B 42 n1 Hex 45
- 27 66 n1 decimal 45
- Software Command Syntax 46
- 1B 68 n1 hex 47
- 27 104 n1 decimal 47
- 1B 77 n1 hex 47
- 27 119 n1 decimal 47
- 0C hex 50
- 12 decimal 50
- 09 hex 50
- 9 decimal 50
- Bar Code Commands 51
- 1B 42 53 n1...n11 hex 52
- 27 66 83 n1...n11 decimal 52
- Code 128 / EAN128 53
- Name Dec Hex 53
- 1B 7C n1 nx Hex 54
- 027 124 n1 nx Decimal 54
- Graphics Commands 55
- 1B 72 n1...n9 hex 56
- 27 114 n1...n9 decimal 56
- 1B 67 n1...n5 hex 57
- 27 103 n1...n5 decimal 57
- 1B 4C n1 Hex 57
- 27 76 n1 Decimal 57
- Print Commands 58
- 1B 6A n1 hex 59
- 27 106 n1 decimal 59
- 1B 51 n1 hex 59
- 1B 81 n1 Decimal 59
- Cut and Present Commands 60
- Eject 1 mm 61
- 05 Hex 62
- 5 Decimal 62
- System Related Commands 63
- 1B 26 50 n1...n2 hex 65
- 27 38 80 n1...n2 decimal 65
- 1B 26 73 0A Hex 65
- 27 38 115 10 Decimal 65
- 1B 00 Hex 66
- 27 0 Decimal 66
- Status Reporting Commands 67
- 1B 05 02 hex 68
- 27 5 2 decimal 68
- 1B 05 04 hex 69
- 27 5 4 decimal 69
- 1B 05 05 hex 70
- 27 5 5 decimal 70
- 2. The printer is printing 71
- 1B 05 45 hex 74
- 27 5 69 decimal 74
- 1B 05 50 n1 hex 75
- 27 5 80 n1 decimal 75
- 1B 06 n1 hex 75
- 27 6 n1 decimal 75
- File Format 76
- Character Bitmap Data 77
- Printing 79
- 5. Print the printout 80
- Default Parameter Settings 81
- Default Value 82
- Examples 82
- Summary of Parameter Settings 83
- 0, 0 (0 mm) 83
- TTP model 84
- 2110 2130 84
- Serial Interface Set-up 85
- Print Setup 86
- Fixed Document Mode 89
- 0, 0 Min 90
- Cut Position Calibration 91
- Wall Compensation (mm) 91
- Printable Area 98
- Page Setup 100
- Simple Calibration Process 101
- FF (Form Feed) 102
- Interface 103
- Setup Options 104
- Parameter Options 104
- USB, TTP 2130 105
- Maintenance 107
- Symptom Suggested Actions 108
- 1. Open the printhead 109
- Firmware 110
- Firmware Identification 111
- Maintenance 112
- Specifications 113
- Ticket Specifications 114
- TOF Detection 115
- Print Module 116
- Ticket Separation 116
- Presenter 116
- Electronics 116
- Text Mode 117
- Miscellaneous 117
- Basic Character Set 118
- Printers 119
- Accessories 119
- Item NA/LA/AP EMEA 119
- Dimensions 120
- Media Holder 121
- 70W Power Supply 122
- 中国 RoHS 材料声明 123
- (China RoHS Material 123
- Declaration) 123
- BM sensor, 95 125
Related products and manuals for Print & Scan Zebra TTP2130
Print & Scan Zebra KR403 Specifications
(158 pages)
(158 pages)
Print & Scan Zebra GX Series User Manual
(4 pages)
(4 pages)
Print & Scan Zebra EPL2 User Manual
(82 pages)
(82 pages)
Print & Scan Zebra R402 User's Guide
(72 pages)
(72 pages)
Print & Scan Zebra R-140 User's Guide
(126 pages)
(126 pages)
Print & Scan Zebra MZ series User Manual
(44 pages)
(44 pages)
Print & Scan Zebra GX430D User Manual
(20 pages)
(20 pages)
Print & Scan Zebra 243 User's Guide
(53 pages)
(53 pages)
Print & Scan Zebra P110 User Manual
(60 pages)
(60 pages)
Print & Scan Zebra Z6M Specifications
(168 pages)
(168 pages)
Print & Scan Zebra TTP7030 Specifications
(144 pages)
(144 pages)
Print & Scan Zebra 105SL Plus User's Guide
(130 pages)
(130 pages)
Print & Scan Zebra P310C Specifications
(84 pages)
(84 pages)
Print & Scan Zebra MtP400 User's Guide
(73 pages)
(73 pages)
Print & Scan Zebra RZ600 User Manual
(4 pages)
(4 pages)
Print & Scan Zebra QLn420 User Manual
(20 pages)
(20 pages)
Print & Scan Zebra EPL2 Specifications
(154 pages)
(154 pages)
© 2020, manymanuals.com. All rights reserved. | 1.146 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals