Zebra TTP2130 Specifications Page 88
- Page / 138
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Default Parameter Settings
Print Setup
88
P1003640-001 TTP2100 Technical Manual 10/22/2008
Print Setup
A long burn time gives darker print. On insensitive paper types you may have to increase the
burn time to get an acceptable print quality.
The main reason to decrease the print speed is to enhance print quality, and to reduce average
current consumption. nics
Controls how the printhead burns the pixels. Four burn pulses give a more even blackness
over the width of the paper and a lower peak current consumption. Two burn pulses give faster
printouts at high burn times. At normal burn times the speed is the same for both settings.;
Selects which font attributes are selected at power ON or after reset. Font attributes bold,
height and width are stored in this parameter.
7
9Default
Burn Time
DRV
1 Min
15 Max
8
19 Default
Max Print Speed
DRV
1 Min
19 Max
n
12345678910111213141516171819
mm/s
47 48 49 50 51 52 53 55 57 61 65 70 77 86 96 107 123 136 150
Note • With firmware version 3.50, do not use settings 18 and 19.
Note • Settings below 15 result in printer chassis resonance causing increased noise and
deteriorated print quality.
10
3Default
Printhead Pulse Control
3 Min
7Max
<ESC>&P<010><003> 2 burn pulses
<ESC>&P<010><007> 4 burn pulses
Caution • 3 and 7 are the only allowed setting, do not set anything else!
12
0Default
Font Attributes
0 Min
255 Max
bits 0-3 Height Multiplier
bits 4-6 Width Multiplier
bit 7 Bold enable
- Zebra® TTP2100 1
- Technical Manual 1
- Contents 3
- Introduction 7
- Contacts 8
- Product Presentation 10
- Print and drop 11
- Print and take 11
- Controls 12
- Description 13
- Installation 15
- Installing a Paper Guide 16
- 11. Press SET 17
- 12. Press STORE 17
- Value When Used 17
- 3. Tighten the screw 18
- Calibrating the TOF Sensor 19
- Installation Considerations 20
- Quick-Fit Hubs 21
- Push down 22
- Ambient Light 24
- Paper low 25
- Connector 25
- Connecting to the Computer 26
- TTP 2130 27
- Connecting the Power 29
- Oscilloscope Setting 2A/div 30
- Self-test 31
- Making a Test Printout 32
- Installing a Printer Driver 33
- Printer Features 35
- Black-mark Settings: 36
- Operation 37
- Loading Fanfold Ticket Stock 38
- Temperature-sensitive 39
- SW96074C 39
- Wrong! Wrong! Wrong! 40
- 1. Open the printer lid 41
- Clearing Paper Jams 42
- Programming 43
- Driver Oriented 44
- ESC ! n1 45
- Select font 45
- 1B 23 Hex 48
- 27 35 decimal 48
- 1B 5A Hex 48
- 27 90 Decimal 48
- Software command syntax 49
- Barcode Commands 53
- Name Dec Hex 55
- 1B 42 57 n1 nx Hex 56
- 027 066 087 n1 nx Decimal 56
- 1B 42 43 n1 hex 56
- 27 66 67 n1 decimal 56
- 1B 7C n1 nx Hex 57
- 027 124 n1 nx Decimal 57
- 1B 62 n1...n5 Data hex 58
- 27 98 n1...n5 Data decimal 58
- 1B 73 nDataHex 58
- 27 115 n Data Decimal 58
- 1B 72 n1...n9 hex 59
- 27 114 n1...n9 decimal 59
- 1B 67 n1...n5 hex 60
- 27 103 n1...n5 decimal 60
- 1B 4C n1 Hex 60
- 27 76 n1 Decimal 60
- Print Commands 61
- Cut and Present Commands 62
- System Related Commands 64
- 1B 26 73 0A hex 67
- 27 38115 10 decimal 67
- 1B 00 Hex 67
- 27 0 Decimal 67
- Status Code Meaning 68
- 1B 05 04 hex 70
- 27 5 4 decimal 70
- 1B 05 05 hex 70
- 27 5 5 decimal 70
- 1B 05 06 hex 71
- 27 5 6 decimal 71
- 2. The printer is printing 72
- 1B 05 0C hex 74
- 27 5 12 decimal 74
- 1B 05 63 hex 74
- 27 5 99 decimal 74
- 1B 05 45 hex 75
- 27 5 69 decimal 75
- 1B 05 50 n1 Hex 76
- 27 5 80 n1 Decimal 76
- 1B 06 n1 hex 76
- 27 6 n1 decimal 76
- Font Loading 77
- Character Bitmap Data 78
- Logotypes 79
- Printing 80
- Status Reporting 81
- Default Parameter Settings 83
- Default Value 84
- Examples 84
- Summary of Parameter Settings 85
- TTP model 86
- 2110 2130 86
- Serial Interface Set-up 87
- Print Setup 88
- Fixed Document Mode 91
- Cut Position Calibration 93
- Wall Compensation (mm) 93
- TOF Sensor Mask 97
- BM Sensor 97
- Printable Area 100
- Page Setup 101
- Simple Calibration Process 102
- Parameters Used 103
- FF (Form Feed) 106
- Interface 109
- Parameter Options 110
- USB, TTP 2130 111
- Maintenance 113
- Symptom Suggested actions 114
- 1. Open the printhead 115
- Firmware 116
- FW version Change 117
- Maintenance 118
- Specifications 119
- Ticket Specifications 120
- TOF Detection 120
- Print Module 121
- Ticket Separation 121
- Presenter 121
- Electronics 122
- Text Mode 122
- Basic Character Set 123
- Miscellaneous 124
- Ordering Number List 124
- Printer Shown on 125
- Dimensions 126
- Media Holder 127
- 70W Power Supply 128
- 150W Power Supply 129
- Part Number: P1003640-001 138
- © 2008 ZIH Corp 138
Related products and manuals for Print & Scan Zebra TTP2130
Print & Scan Zebra 2443 Service Manual
(76 pages)
(76 pages)
Print & Scan Zebra P300i User Manual
(48 pages)
(48 pages)
Print & Scan Zebra LI 72 User's Guide
(86 pages)
(86 pages)
Print & Scan Zebra 10/100 User's Guide
(106 pages)
(106 pages)
Print & Scan Zebra ZE500 User's Guide
(170 pages)
(170 pages)
Print & Scan Zebra GX420t User's Guide
(108 pages)
(108 pages)
Print & Scan Zebra EPL2 Specifications
(138 pages)
(138 pages)
Print & Scan Zebra KR203 Specifications
(36 pages)
(36 pages)
Print & Scan Zebra TLP 2824 User's Guide
(60 pages)
(60 pages)
Print & Scan Zebra P120i User Manual
(76 pages)
(76 pages)
Print & Scan Zebra 170PAX2 Series User's Guide
(100 pages)
(100 pages)
Print & Scan Zebra LI 72 User's Guide
(2 pages)
(2 pages)
Print & Scan Zebra P520 User Manual
(64 pages)
(64 pages)
Print & Scan Zebra 2844 Printer User's Guide
(54 pages)
(54 pages)
Print & Scan Zebra 170PAX4 User's Guide
(164 pages)
(164 pages)
Print & Scan Zebra Z6Mplus User's Guide
(142 pages)
(142 pages)
Print & Scan Zebra EM 220 Service Manual
(53 pages)
(53 pages)
© 2020, manymanuals.com. All rights reserved. | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals