Zebra ZT210 User Manual Page 96
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Printer Configuration and Adjustment
Changing Printer Settings
96
P1048261-004 8/22/12
Port Settings
Table 12 • Port Settings
Baud Rate Set the Baud Rate
Select the baud value that matches the one being used by the host computer.
Accepted values:
• 115200
• 57600
• 38400
• 28800
• 19200
• 14400
• 9600
• 4800
Related ZPL command(s):
^SC
SGD command used:
comm.baud
Control panel menu item: BAUD RATE on page 36
Printer web page:
View and Modify Printer Settings >
Serial Communications Setup
Data Bits Set the Data Bits Value
Select the data bits value that matches the one being used by the host computer.
Accepted values:
• 7
• 8
Related ZPL command(s):
^SC
SGD command used:
comm.data_bits
Control panel menu item: DATA BITS on page 36
Printer web page:
View and Modify Printer Settings >
Serial Communications Setup
Parity Set the Parity Value
Select the parity value that matches the one being used by the host computer.
Accepted values:
• NONE
• EVEN
• ODD
Related ZPL command(s):
^SC
SGD command used:
comm.parity
Control panel menu item: PARITY on page 36
Printer web page:
View and Modify Printer Settings >
Serial Communications Setup
- ZT210™/ZT220™/ZT230™ 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- HOME MENU 18
- SETTINGS 18
- ▼ XXXXXXX ▲ 19
- SETTINGS Menu 20
- SETTINGS Menu (continued) 21
- TOOLS Menu 24
- TOOLS Menu (continued) 25
- NETWORK Menu 28
- NETWORK Menu (continued) 29
- LANGUAGE Menu 32
- LANGUAGE Menu (continued) 33
- SENSORS Menu 34
- SENSORS Menu (continued) 35
- PORTS Menu 36
- PORTS Menu (continued) 37
- Types of Media 38
- Printer Setup and Operation 39
- Ribbon Overview 40
- Adhesive Test 41
- Ribbon Scratch Test 41
- Printer Setup and 43
- Operation 43
- Handling the Printer 44
- I) may damage the 46
- Data Cables 48
- 115 V AC 49
- 230 V AC 49
- Power Cord Specifications 50
- Select a Print Mode 52
- Load the Ribbon 55
- Printer Setup 56
- Load the Media 60
- Roll Media 61
- Fanfold Media 61
- Roll Media (Continued) 62
- Fanfold Media (Continued) 62
- If using… Then… 64
- Liner Take-Up) on page 68 65
- Mode on page 74 65
- Final Steps for Tear-Off Mode 66
- 11. Close the media door 67
- 23. Close the media door 73
- Final Steps for Cutter Mode 74
- 30. Close the media door 76
- Printer Configuration 77
- Changing Printer Settings 78
- Print Settings 79
- • THERMAL TRANS 80
- • DIRECT THERMAL 80
- • TEAR OFF 81
- • CUTTER 81
- Print Listings on Label 83
- Important • 87
- Directory Listing 88
- Network Settings 89
- Print Server Settings > 91
- Factory Print Server Settings 91
- Language Settings 92
- • ZPL II 94
- Sensor Settings 95
- Port Settings 96
- Serial Communications Setup 97
- MEDIA/RIBBON CAL 98
- LOAD BACKING 99
- REMOVE RIBBON 99
- Remove the ribbon (if used) 100
- CALIBRATING 101
- PLEASE WAIT 101
- RELOAD ALL 101
- CONTINUE 101
- Close the printhead 102
- Close the media door 102
- Reload the ribbon (if used) 102
- Adjust the Printhead Pressure 103
- If the media... Then 104
- Adjust Ribbon Tension 106
- Remove Used Ribbon 107
- Routine Maintenance 109
- Area Method Interval 110
- Printer Exterior 111
- Media Compartment and Sensors 111
- Raise the media door 113
- 8. Close the media door 115
- Clean the Peel Assembly 116
- Clean the Cutter Module 120
- Remove the cutter shield 121
- Replacing Printer Components 124
- Lubrication 124
- Troubleshooting 125
- Troubleshooting Checklist 126
- Meaning of Indicator Lights 127
- Printing Issues 129
- Ribbon Problems 132
- Error Messages 134
- RIBBON OUT 135
- PH NOT AUTHENTICATED 135
- REPLACE PRINTHEAD 135
- Display/ 137
- Indicator Lights 137
- Communications Problems 138
- Miscellaneous Issues 139
- Printer Diagnostics 141
- CANCEL Self Test 142
- PAUSE Self Test 143
- FEED Self Test 144
- Print Quality Description 145
- FEED + PAUSE Self Test 147
- CANCEL + PAUSE Self Test 147
- FE indicates a framing error 148
- PE indicates a parity error 148
- NE indicates noise 148
- Sensor Profile 149
- Specifications 151
- General Specifications 152
- Printing Specifications 153
- Ribbon Specifications 153
- Media Specifications 154
- Glossary 155
- 8/22/12 P1048261-004 159
- P1048261-004 8/22/12 160
- 8/22/12 P1048261-004 161
Related products and manuals for Label printers Zebra ZT210
Label printers Zebra Z4Mplus User Manual
(178 pages)
(178 pages)
Label printers Zebra QL+ User Manual
(86 pages)
(86 pages)
Label printers Zebra PA/PT 400 User Manual
(44 pages)
(44 pages)
Label printers Zebra GX420 User Manual
(4 pages)
(4 pages)
Label printers Zebra PA400 User Manual
(58 pages)
(58 pages)
Label printers Zebra Cameo User Manual
(22 pages)
(22 pages)
Label printers Zebra 79695L-002 User Manual
(156 pages)
(156 pages)
Label printers Zebra ZM400 User Manual
(33 pages)
(33 pages)
Label printers Zebra Z4M User Manual
(102 pages)
(102 pages)
Label printers Zebra AM16629-1 User Manual
(12 pages)
(12 pages)
Label printers Zebra A100 User Manual
(28 pages)
(28 pages)
Label printers Zebra ZP 450 User Manual
(82 pages)
(82 pages)
Label printers Zebra XiII-Series User Manual
(118 pages)
(118 pages)
Label printers Zebra XiIII Series User Manual
(116 pages)
(116 pages)
Label printers Zebra Z4M User Manual
(57 pages)
(57 pages)
Label printers Zebra 105SL User Manual
(130 pages)
(130 pages)
Label printers Zebra Printers User Manual
(69 pages)
(69 pages)
Label printers Zebra LI 72 User Manual
(62 pages)
(62 pages)
© 2020, manymanuals.com. All rights reserved. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals