Zebra 105SL User Manual Page 64
- Page / 174
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- SETUP/EXIT button 13
- About This Document 14
- Introduction 15
- External View 16
- Control Panel 17
- Control Panel LCD 18
- Control Panel Buttons 18
- Control Panel Lights 19
- Printer Media Compartment 21
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Connector Locations 27
- Types of Connections 28
- Data Cable Requirements 30
- 4. Turn on (I) the printer 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- Adhesive Test 36
- Ribbon Scratch Test 36
- Operations 37
- Media Loading Overview 38
- Insert Media into the Printer 39
- Fanfold Media 40
- If… Then… 41
- Load Media in Tear-Off Mode 42
- Load Media in Peel-Off Mode 46
- If the printer has 47
- 1). Insert the long end 51
- If... Then 55
- Pull out the spindle hook 56
- Load Media in Rewind Mode 57
- 1) and the adjustable hook 58
- 2) point down 58
- Load Media in Cutter Mode 65
- Load Ribbon 69
- Remove Used Ribbon 73
- Adjust Media Sensors 74
- Lower Media Sensor 75
- Adjust Printhead Balance 76
- Printhead Pressure Adjustment 78
- Calibrate the Printer 79
- Setup Mode 82
- Exit Setup Mode 83
- Default Password Value 84
- Print a Configuration Label 85
- LIST NETWORK 86
- TEAR OFF +000 88
- - + 88
- PRINT MODE 88
- -TEAR-OFF + 88
- Action/Explanation 89
- PRINT WIDTH 90
- - MM + 90
- MAXIMUM LENGTH 91
- -39.0 IN 988 MM 91
- To format a memory card: 93
- To initialize Flash memory: 94
- SENSOR PROFILE 95
- PRINT 95
- To change the value shown: 100
- Parameter 100
- LEFT POSITION 102
- - ±0000 + 102
- HEAD RESISTOR 103
- - 0500 OHMS + 103
- To skip these parameters: 104
- Print Server LCD Displays 106
- ^WE ZPL command to set 108
- PLUS (+) to select YES 109
- Parameter Action/Explanation 109
- Configuration 110
- Control Panel Parameters 110
- PC and Memory Cards 111
- PCMCIA PC Cards 112
- PAUSE light flashes 113
- PAUSE light flashes only 113
- Routine Maintenance 115
- Lubrication 116
- Cleaning Schedule 116
- Clean the Exterior 117
- Take-label sensors 121
- Black mark sensor 121
- Ribbon sensor 121
- Clean the Snap Plate 122
- Clean the Cutter 123
- Replace the Fuse 124
- Troubleshooting 125
- Troubleshooting Checklists 126
- LCD Error Messages 127
- LCD Display/ 128
- Printer Condition 128
- HEAD COLD 129
- OUT OF MEMORY 129
- (function) 129
- Print Quality Problems 130
- Note • A vertical drift of 132
- Calibration Problems 133
- Communications Problems 134
- Ribbon Problems 135
- LANGUAGE 136
- SAVE CHANGES in the 136
- Calibrate 137
- Printer Diagnostics 138
- CANCEL Self Test 139
- PAUSE Self Test 141
- FEED Self Test 142
- Print Quality Description 144
- FEED and PAUSE Self Test 146
- Sensor Profile 148
- Specifications 149
- General Specifications 150
- Communications Specifications 151
- Other Standard Features 151
- Additional Options 151
- Agency Approvals 152
- Printing Specifications 153
- Ribbon Specifications 153
- Media Specifications 154
- Bar Codes 155
- Glossary 157
- End User License 161
- Agreement 161
- End User License Agreement 162
- HEAD COLD message, 121 168
- HEAD TOO HOT message, 120 168
- OUT OF MEMORY message, 121 169
- PAPER OUT message, 120 170
- RIBBON IN message, 120 171
- RIBBON OUT message, 119 171
- © 2006 ZIH Corp 174
© 2020, manymanuals.com. All rights reserved. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals