Zebra A300 User's Guide

User's GuideA300ZebraCustomer order #55530LManufacturer part #55530LB© Zebra Technologies CorporationZEBRA PERSONAL PRINTER LINEDIRECT THERMAL P

1255530lr4 Page 5 Wednesday, March 26, 1997 11:18 AM

3455530lr4 Page 6 Wednesday, March 26, 1997 11:18 AM

5612355530lr4 Page 7 Wednesday, March 26, 1997 11:18 AM

7855530lr4 Page 8 Wednesday, March 26, 1997 11:18 AM

1255530lr4 Page 9 Wednesday, March 26, 1997 11:18 AM

Figure 2: Parallel Connection55530lr4 Page 10 Wednesday, March 26, 1997 11:18 AM

Figure 3: Serial Connection55530lr4 Page 11 Wednesday, March 26, 1997 11:18 AM

Note: If you plan to use BAR-ONE software to create your labels, you will need to install the software on your computer before you can operate your pr

The A300 printer uses BAR-ONE software or ZPL II Programming Lan-guage sent from any Windows™ or DOS application.1. Start Windows.2. Insert disk 1 of

Located on the right-hand side of the printer near the back. The power switch should be turned off before connecting or discon-necting any cables.In n

Zebra® A300User’s GuideCustomer order # 55530LManufacturer part # 55530LB Rev. 455530lr4 Page -3 Wednesday, March 26, 1997 11:18 AM

Zebra A300 & T300User's GuideAddendum1C:\A_Series\A_T_Adden.vpWed Aug 12 10:52:06 1998Color profile: DisabledComposite Default screen

ScopeThis addendum contains information about the new Calibration featuresadded to the Zebra A300 and Zebra T300 printers when upgraded with the25.8.1

Manual CalibrationManual calibration should be performed whenever you are using pre-printed labels or preprinted label backing, or if the printer will

© Zebra Technologies Corporation Part # 55560L Rev. 1Figure 2. T300 Sample Media Sensor ProfileFigure 1. A300 Sample Media Sensor Profile4C:\A_Series\

Turn the printer on by pressing the Power Switch on the right side of the printer. The Power and Fault lights will turn on. The printer performs a set

6. Press and release the Feed Key. A profile of the media sensor settings will print. When complete, the printer will save the new settings in memory

Here is the command description for the Set Communications command (refer to your ZPL II Programming Guide for additional programming information):^SC

CAUTION: Use only the cleaning agents indicated in the following table. Zebra Technologies Corporation will not be responsible for any other fluids be

Table 4. TroubleshootingPower light does not turn on when Power switch is turned on.Printer is not receiving power.Make sure that the power supply is

To print out a listing of the printer’s current configuration (configuration label), refer to Table 1, “Feed Key Troubleshooting Modes,” on page 14.If

This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating

Figure 6: Communications Diagnostics Printout (Sample)55530lr4 Page 21 Wednesday, March 26, 1997 11:18 AM

Table 5: SpecificationsPrint density 203 dots/inch 8 dots/mmPrint width 1 to 4.125 25.6 to 105.0 mmPrint speed 2 /sec 51 mm/secLabel width (including

Media requirements Zebra recommends use of Zebra brand media. All media must be direct thermal media. Media may be continuous, die-cut, or notched. No

Figure 7. 230 VAC Power Line CordFigure 8. Examples of International Safety OrganizationsTable 6. Parallel Pinouts1 Strobe2-9 Data Bits 0-710 Acknowle

The enclosed software and documentation are protected by the United States copyright law and international treaty, and there-fore you must treat them

1. Printer WarrantyZEBRA printers, excluding thermal printheads which are warranted separately below, are warranted against defects in material or wor

User's GuideA300ZebraCustomer order #55530LManufacturer part #55530LB© Zebra Technologies CorporationZEBRA PERSONAL PRINTER LINEDIRECT THERMAL P

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Unpacking and Inspection. . . . . . .

Figure 1: Printer Overview Media cover Media holder Media guides Tear bar Printhead Print mechanism latches Peel-off roller Peel-off d

This manual provides all of the information you will need to operate your printer on a daily basis. To print labels, tags, or tickets with the A300 pr

1255530lr4 Page 2 Wednesday, March 26, 1997 11:18 AM

3455530lr4 Page 3 Wednesday, March 26, 1997 11:18 AM

56712355530lr4 Page 4 Wednesday, March 26, 1997 11:18 AM